100BASE - FX SFP Fiber Optical Transceiver Module , 1 Gbe Sfp Sx Fiber Transceiver

100BASE-FX , LC , Dual Fiber , 1310nm , SMF , 20km , SFP Optical Transceiver Module

Features

• Up to 155Mbps data-rate

• 1310nm FP laser and PIN photo detector for 20km transmission

• Compliant with SFP MSA and SFF-8472 with duplex LC receptacle

• Digital Diagnostic Monitoring:

Internal Calibration or External Calibration

• Compatible with RoHS

• +3.3V single power supply

• Operating case temperature:

Commercial : 0 to +70°C

Industrial : -40 to +85°C

Applications

• SDH STM-1, S-1.1,L-1.1, L-1.2

• SONET OC-3 IR1,LR1,LR2

• Other optical links

Description

The SFP transceivers are high performance, cost effective modules supporting 155Mbps data-rate and 20km transmission distance with SMF.

The transceiver consists of three sections: a FP laser transmitter, a PIN photodiode integrated with a trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety requirements.

The transceivers are compatible with SFP Multi-Source Agreement (MSA) and SFF-8472. For further information, please refer to SFP MSA.

Absolute Maximum Ratings

Table 1 - Absolute Maximum Ratings

Recommended Operating Conditions

Table 2 - Recommended Operating Conditions

Optical and Electrical Characteristics

Table 3 - Optical and Electrical Characteristics

Notes:

1. The optical power is launched into SMF.

2. PECL input, internally AC-coupled and terminated.

3. Measured with a PRBS 2²³-1 test pattern @155Mbps, BER ≤1×10^-10

4. Internally AC-coupled.

Timing and Electrical

Table 4 - Timing and Electrical

Diagnostics

Table 5 – Diagnostics Specification

Digital Diagnostic Memory Map

The transceivers provide serial ID memory contents and diagnostic information about the present operating conditions by the 2-wire serial interface (SCL, SDA).

The diagnostic information with internal calibration or external calibration all are implemented, including received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage monitoring and temperature monitoring.

The digital diagnostic memory map specific data field defines as following.

Pin Descriptions

Notes:

Plug Seq.: Pin engagement sequence during hot plugging.

1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.

2) TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7k~10kΩ resistor. Its states are:

Low (0 to 0.8V): Transmitter on

(>0.8V, < 2.0V): Undefined

High (2.0 to 3.465V): Transmitter Disabled

Open: Transmitter Disabled

3) Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7k~10kΩ resistor on the host board. The pull-up voltage shall be VccT or VccR.

Mod-Def 0 is grounded by the module to indicate that the module is present

Mod-Def 1 is the clock line of two wire serial interface for serial ID

Mod-Def 2 is the data line of two wire serial interface for serial ID

4) LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor. Pull up voltage between 2.0V and Vcc+0.3V. Logic 1 indicates loss of signal; Logic 0 indicates normal operation. In the low state, the output will be pulled to less than 0.8V.

5) RD-/+: These are the differential receiver outputs. They are internally AC-coupled 100 differential lines which should be terminated with 100Ω (differential) at the user SERDES.

6) TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100Ω differential termination inside the module.

Established in 2001& headquartered in Shenzhen, E-link China Technology Co., Ltd. (E-link) is a leading Fiber Optic Communication and CCTV Security Transmission product manufacturer in China. Our main products include active equipments including fiber media converters, CCTV fiber converters, CCTV over Ethernet Converters (HD-SDI over Ethernet, HDMI over Ethernet, Power over Ethernet), etc. With rich experience in providing high quality products in telecom and CCTV business, E-link has a large manufacturing base in Shenzhen, able to deliver cost-effective solutions to serve our customers successfully.

E-Link Quality:

• ISO9001 Quality System

• Full-Spectrum environment and electrical testing of all product design

• 48 hours aging test before delivery

• Qualified CE, RoHS, FCC

Since the launch of our products on the domestic market and international market, we have won a good reputation for our high quality products and sincere services. Our products are widely applied to network systems of Telecom, Radio and Television, Public Security, Bank ,ect. To be in line with different needs of different customers, we have people to trace the latest market information so as to keep our products competitive and vital.

Our knowledgeable sales, technical support and engineering staff are dedicated to understanding your requirements and designing products & solutions to meet your needs. We shall be pleased to provide you fiber optical network products with our best price, superior quality and fast delivery.