1800MM 3 Ply Corrugated Cardboard Production Line 100m / Min For Cardboard Making​

3 Ply 1800MM 100m Per Min Corrugated Cardboard Production Line For Cardboard Making​

※main technical parameters and requirements in production line

1, The maximum production width of the corrugated cardboard:1800mm

2, Design speed:100m/min

3, Economic speed:60-80m/min

note:Production line speed test paper should meet the following requirements:(the surface temperature of the equipment is not less than 172℃)

﹡Paper rating of not less than B grade ﹡Paper moisture content of about:11%±2%

﹡top paper:100—250g/m2 ﹡core paper:100--250g/m2

﹡corrugated paper:100—200g/m2

4, Flute-type combination:A ,C, B, E(as customers’ requirement)

5, Steam the necessary requirements:

﹡amount of steam 2500—3000Kg/Hr ﹡the highest pressure:1.2MPa

﹡common pressure:0.8-1.1MPa

6,power supply:380V 50Hz Three-phase four-wire system

7,equipment installed total power:about120Kw The actual power consumption:about 60Kw(full speed)

8,equipment covers:about38m×10m×5m(Specific length of foundation Figure prevail)

9,Equipment out of paper orientation:According to the user to determine the transmission plant set left or right position

10,Equipment applicability,Available in A, B, C class domestic or imported paper Paper

Customer-owned section

1,steam heating system:proposal with 2000Kg / Hr of a steam boiler pressure:1.25MPa steam pipeline.

2,air compressed machine,air pipeline,glue conveying pipe.

3,power supply,wires connected to the operation panel and line pipe.

4,water sources,water pipelines,buckets and so on.

5,Water, electricity, gas flush mounting civil foundation.

6,Test with the base paper,corn starch (potato),Industrial use caustic soda,borax and other material.

7,Oil equipment,lubricating oil,hydraulic oil,lubricating grease.

8,installation,commissioning of food, accommodation.And provide installers with the installation.

※SF-280S fingerless type single facer

※Structural features:

★Adopt vacuum suction structure, with high pressure strong blower.Suction with silencer.Gas supply and electrical control cabinet to focus on the same operation cabinet,not less than 1.5 meters away from the host,Fully enclosed full operation side.

★base and wallboard cast iron wall,Wallboard thickness130mm.universal Joints.

★corrugated roller material adopt 48CrMoalloy steel,quenched,Laser hardening,Surface finish,main roll of corrugated diameter¢ 280mm,surface hardnessHRC60degree above.The key parts of the tile and pressure roller bearings Wafangdian produce high temperature bearings.

★pressure roller ¢ 284mm,surface grinding and chrome-plated；cylinder control and remove up and down, 45 carbon steel materials, quenching (with cushioning devices).

★pneumatic control glue to glue back, glue roller diameter ￠215mm,Engraved polished surface after a 36-line pit style textured machined chrome plated,after scraping the roller surface polished hard chrome plated.

★Corrugated roller, pressure roller materials provided by the Central Plains Steel,High on corrugating unilateral 0.15mm, 0.075mm high pressure roller unilateral. Plus stopper. ¢ 160mm cylinder with compression cylinder.

★preheat roll adopt seamless steel pipe production by tiangang ¢ 300mm,connecting with metal Hose.

※regular technical parameters:

1,effective width:1800mm 2,operation direction:left or right(determined in accordance with customer plant)

3,design speed:100m/min 4,temperature range:200—260℃

5,corrugated flute:(UV type or UVV type)

※roller diameters parameters:

1,diameter of corrugated roller: ￠280mm 2,diameter of pressure roller: ￠284mm

3,diameter of glue roller: ￠216mm 4,diameter of preheat roller: ￠320mm

※powered motor parameters:

1,main drive motor:7.5Kw rated voltage:380V 50Hz Continuous (S1) working standard

2,suction motor:7.5Kw rated voltage:380V 50Hz Continuous (S1) working standard

※main purchased parts,materials and place of origin: