Small Space Occupancy Closed Cooling Tower With 235 M3/H Work Flow Rate

Small Space Occupancy Closed Cooling Tower With 235 M3/H Work Flow Rate

Advantages for cooling towers

1) Closed loop
Preventing the impurities into the system to block the cooling tubes, soft water is adopted to avoid overheating caused by scaling to the water pipes.

2) Automatic temperature control
Automatic start/stop spraying system to achieve effective control on the temperature of cycled cooling water, the temperature of the cooling water can be controlled below 40 ℃. With this function, the water & energy cost is reduced to the lowest point with intelligent control to the number of working fans and start & stop of spray pump.

3) No need of water pool and cooling tower
Low cost, small space occupancy, easy installation and move with the welder.

4) Cooling system structure
Galvanized iron beam.

5) High efficiency heat exchange
Four side air inlet louvers supply sufficient amount of wind blowing through cooling coils taking most of the heat away, which effect is strengthened via spray cooling water running through the cooling coils

3.6 Application Conditions

• Environment:

(1)Altitude lower than 3000m；

(2)Wet Bulb Temperature below 32℃, Anti-freeze required below 0℃ dry bulb temperature.

(3)Average value of daily maximum relative humidity during the wettest month at the operation site shall not exceed 90%.

(4)The most harmful atmospheric conditions are those with large existence of industrial smoke, chemical fumes, salt or heavy dust. Such airborne impurities are carried into the cooling tower and absorbed by the spray water to form a corrosive solution, in which cases special attention shall be paid to the water treatment system and cooling tower construction materials.

• Installation:

(1) Site diagram is to be provided by the client.

(2) Requirement for the base:smooth concrete ground surface or slabs is; metal frame base is also acceptable.

(3) For better cooling performance, the cooling towers should be placed where exist good ventilation and sun light shelter (direct sunlight will considerably increase spray water temperature).

• Storage:

The closed circuit cooling tower shall not be covered by plastic film for long term warehouse stock to avoid accelerating corrosion to PVC materials.

1. Technical Specifications & Supply Scope

Customer benifits

Atteractive shape:Small dimension of shape,low height of tower,light weight of tower ,light weight of tower and multiform layout in covering area.
Advanced structure:The design of structure is superior,and it reaches an advance level the same as the products abroad.
Light Weight ang high strength::Cooling tower baby is made of FRP,which is of ageing-resistance and corrision-resistance,co that the bady will never be fading and transfirmation.The tower can bear an earthquake of 8grade on the richer scale and suffer 12 grade typhoon.
Super low noise: Adopting super low-noise fan and unique noise eliminatiom technology,the noise level is the leading position.
Less expense:Motor output is 30 percent less than the same product of other factories.The cooling water can be used in enclosed circulating,so it can reduce a lot of expenses when equipment runing.
Less drift loss:Adoping advanced drift-eliminator,the drift loss can be reduced to 0.001 perent,and has appostive effect on the environmental protection
Reliable in use:Use of hot dip galvanized steel stent treatment, anti-corrosion ability, service life of more than twice as similar produc

Shanghai Yanye industrial Cooling Equipment Co., Ltd ( YANYE Cooling ) is a manufacturing plant for provision of various industrial & commercial cooling solutions. The system ranges from the cooling of water to gas, oil and miscellaneous industrial fluid mediums, with a strong emphasis on the manufacturing of closed circuit cooling towers and evaporative condensers.

Located in both Shanghai and Wuxi cities, YANYE Cooling owns one of the largest production scope of modern closed circuit cooling tower and evaporative condenser manufacture in China, covering an area of approx. 30.000 square meters, with an assembly workshop of 18,000 square meters.

With superb quality and exquisite manufacture technique, Yanye Cooling has won wide recognition from customers in the fields of heat treatment, metal & plastic melting, forging, air conditioning, compressor, power plant and chemical industries etc. With great reputation, WELL is honorable to have supplied her cooling systems to AGC(Japan), Saint-Gobain (France), Vaillant (Germany), Sanmina-SCI (USA), Danaher (USA), Stanly (USA), Aichelin (Austria), Mecaplast (France) and China Telecom etc global leading images.

With constant enthusiasm, YANYE COOLING team is working toward the goal of becoming one leading enterprise in the international lines.